Stolen Mustang

Increasing your cars performance by modding the exhaust.system

In the never ending quest for lower drag times a car tuner will often times start with removing the restrictive factory exhaust system and decreasing backpressure. A complete exhaust revamp can consist of anything from a header(s) to a cat-back exhaust system. Choosing which one is right for you is a task that must be undertaken with consideration to your local street laws.

Headers: The factory exhaust manifold is usually a bulky cast-iron unit that is designed to deliver low-end torque (provided by the small primaries). While this is desirable for daily-driving, it is not the ideal for performance. Many factors can affect a headers performance but generally the features you should be concerned with are:

• Primary Width – Wider the primaries the more peak torque (but later in the power band). There is a limit to how big is big enough that varies from engine to engine.
• 4-1 or 4-2-1 Design. A 4-1 design incorporates all 4 primaries intersecting into the collector whereas the 4-2-1 has the primaries split into twos and then into one. Different designs offer different power bands.
• Type of steel- No question here, what you want is SS for the highest quality and most corrosive resistant header(s).

Catalytic Converters

While usually pin pointed as the main restriction in an exhaust, nothing can be further from the truth, while true catalytic converters do restrict flow just like anything else in the pathway of the exhaust gases; they do not hinder flow anymore than the muffler. In fact most catalytic converters are less of a restriction than a muffler. I would always opt for a high flow catalytic converter in an emissions state. These have been proven to provide a negligible loss in horsepower while still keeping it road legal.

Exhaust Piping

Becuase of the budget/time that’s put into both R&D and producing a factory auto, the exaust tubing is usually a ho hum choice. Just like the stock exhaust manifold, it suffers from too small diameter piping and crushed bends. When replacing the entire exhaust system always look for a mandrel bent system (small exhaust shops cannot offer this service) that is also stainless steel. The mandrel bends are somewhat more important than the overall size of the exhaust.

Picking the diameter is a fairly easy decision and should be followed by a general outline such as this:

• 2″ Stock- Very Mildly Modified

• 2.25″ Mildly Modified-Moderate (exhaust,header,cold air intake,tune)

• 2.5″ Moderately Modified- Built N/A engine (exhaust, header, cold air intake, tune, pistons, rods)

• 3″ Forced Induction – Turbo or SuperCharged

Mufflers

Look for a straight through design from a respected name. Magnaflow, Flowmaster, Walker, and Thrush are just a few of the better performance muffler outfits. Glasspack mufflers tend to be a good compromise of performance at a lower price.

About the Author

94-97 Ford Mustang Adjustable Fuel Pressure Regulator $79.00

05-10 Mustang GT Intake Manifold Plenum Cover Aluminum No Finish $69.99

SUPERIOR FORD AOD TRANSMISSION HIGH PERFORMANCE SHIFT KIT MUSTANG TRUCK KAOD-HP $58.99

BBK Cold Air Induction System 1718 96-04 Mustang 4.6 GT $134.95

Shelby Performance Parts 6 Speed Shifter for Shelby Mustang $150.00

99 00 FORD MUSTANG LEFT DRIVER RIGHT PASSENGER AIR BAG AIRBAG TAN BEIGE SET 1999 $300.00

MPC Flip Out Mustang $45.00

1.25-INCH WIDE 5 X 4.5 FORD MUSTANG CROWN VIC RANGER WHEEL SPACERS ADAPTERS 5LUG $59.99

Parts Lot 3 1:16 Scale Model Cars Mustang 57 Chevy Duster Revellution 1 of 5000 $1.00

05 06 07 08 FORD MUSTANG CHASSIS ECM FUEL PUMP CONTROL MODULE UNIT 6R3A-9D372-BA $79.00

BILLY CANNON AUTO THROWBACK MINI HELMET LSU MUSTANGS HEISMAN 1959 $52.99

HOT WHEELS 2009 REGULAR FORD MUSTANG TREASURE HUNT WITH VHTF RED MOTOR $13.53

GT45 13PC TURBO KIT TURBOCHARGER+MANIFOLD+DOWNPIPE+WG 79-93 FORD MUSTANG 5.0L V8 $774.98

99-04 MUSTANG 1PC HALO PROJECTOR LED BLACK HEADLIGHTS $82.99

1971 Ford Mustang Factory Cobra Jet Rochester Quadra Jet Carburetor 7040286 Carb $825.00